Posts Tagged ‘Servo’
Kraken 580 heli. Lucky the servo horns broke and servos ok. Gyro orientation correct this time.
Video Rating: / 5
Related
5 dolla metal gear cyclic servos and 7 dolla futaba clone tail servo TREX 450 clone news
why waste 25 to 50 dollars per servo to learn with ? more info on my forum
http://wickedrc.proboards.com
http://www.futaba-rc.com Futaba Video Update. In this segment Steve Kaluf shows the features of the new S.bus System.
Stop cable clutter with the innovative S.Bus system. It uses digital serial data communication technology to transmit control signals between your receiver and servos. A single S.Bus cable can carry signals to as many channels as your transmitter can handle. You no longer have to worry about plugging in the wrong servo to the wrong channel, because each servo knows what channel it is dedicated to in advance.
S.Bus receivers are limited only by the number of channels
your transmitter will handle. Dont have S.Bus servos? No
problem. SBD-1 S.Bus Decoder Cables let you use existing analog and digital servos, too. The Futaba S.Bus system is nothing short of revolutionary and the revolutions just beginning.
• Eliminates clutter
• Easy programming with the SBC-1 Channel Setting Tool, S.Bus receivers or PCLink software
• No receiver channel limits (except by those on your transmitter)
• Plug in battery packs anywhere you wish
• Heavy-duty 20-gauge wire
• SBD-1 decoder cables (sold separately) let you use existing analog and digital servos
• Prevents mismatched servo-channel connections
• S.Bus system accessories make any installation simple
Video Rating: / 5
Related
RC Heli tail servo problem
My tail servo doesn’t go back to it’s position.I don’t know what’s going on. It just basically get stuck at the position it was put at.
Related
Walkera V120D02S is it really a servo delay issue
In this video clip is my rationalization to this so referred to as servo delay situation on this new walkera helicopter V120D02S. as for every my expertise, I have described things and information proper and I think there is no problem there. At the end of this video clip you can see some 3D flight clips. Full video clips of 3D flight evaluations coming soon. Comments and suggestions welcome at alishanmao@gmail.com , details@onlyflyingmachines.com or ali@redcatracing.com Never fail to remember to go to www.onlyflyingmachines.com , http and Subscribe to www.youtube.com
Related
Trex 250 Tail Rotor Servo Tip
I set my tail rotor up precisely the identical way as demonstrated in RC heli journal, but didn’t like it. This is what I did.
Related
HK450 RC Heli (TREX450 Clone) – Testing HXT900 9g Servo and SKYA LX303 HH gyro on the tail.
Testing the tail holding ability of a HXT900 9g Servo with a SKYA LX303 Heading Hold Gyro on a Hobbycity HK450 (TREX450SA clone) RC Helicopter. Doing a couple of hard punches on the collective to see the effect. Details: Hobbycity HK450 Heli HXT900 9g Servo on tail SKYA LX303 HH Gyro Esky 3800kV Brushless Outrunner Motor Esky 25A ESC Align 11T pinion Superhero 2200mAH 25C 3S Lipo 11.1V Towerpro 9g servos on cyclic Spektrum AR7000 receiver Spektrum DX7 Transmitter 325mm Fibreglass mainblades
Video Rating: 4 / 5
Related
Tragic RC Helicopter Crash, Servo Failure Piroflip Onboard Camera Insane 3D Funny Accident Car Heli
Crash caused by a stripped gear of the rear swash plate servo at a Piroflip. No electronics impaired (only 2 servo gears and motor fan). So this crash is really nickel-and-dime (100- 150 Euro) 🙂 Music: Mozart- Requiem Setup: Standard Thunder Tiger Mini Titan E325 Aluminum rotor head Aluminum washout base Kontronik Jazz 40-06-18 Hacker A20-6XL Kokam 2100 11,1V 30C H5 3x Thunder Tiger C1016 1x Futaba S3114 Robbe- Futaba GY-240 Hyperion 325 Carbon Fiber Blades Align Tail Rotor Blades for T-Rex 450 (plastic) Graupner- JR MX-16S, 40 Mhz Graupner- JR R16-SCAN Approx. 2800 rpm at head Weight 942 g with downed FlyCamOne2 Improved FlyCamOne2: Replaced the accu with a 1400 mAh Cell, weighs now 62 g (+21g)
Video Rating: 3 / 5
Related
